Denso RC5 Especificaciones descargar pdf (Pagina 119)

107

11.3 Setting the Jumpers and DIP Switch on the RS-232C

Extension Board

Set the jumpers and DIP switch on the RS-232C extension board as shown below.

Jumper/DIP SW SW1 JP1 JP2 JP3

Settings Set selectors 1

and 3 to ON.

Set a jumper cap onto

pin 14.

Set a jumper cap

onto NC.

Seta a jumper cap

onto NC.

1234

SW1

9 3 4 5 6 7 10 11 12 14 15 NC

JP1

JP2

JP3

1 2 ... 114 115 116 117 118 119 120 121 122 123 124 ... 137 138

OPTIONS MANUAL 1
Important 3
[F5 Input ID] 4
The serial number appears 5
How this book is organized 7
Contents 9
PART 1 OPTIONAL OPERATION 13
1.3.1 Specifications 15
1.3.2 Outer Dimensions 16
What is Pendantless State? 17
Setting the Pendantless State 17
Pendantless State Precautions 17
Procedure 19
Chapter2 Operating Panel 20
TP socket 22
Operating panel face 23
To be secured 23
M4 screw 23
(5 mm or more) 23
(In version 1.7 or later) 25
3.3.1 Specifications 27
3.3.2 Outer Dimensions 28
Saving programs and data 29
Getting a snapshot 29
Chapter4 30
× 480 or higher 31
4.3 Communications Cable 32
CONTROLLER 33
Chapter6 40
6.1.1 Location of the µ 42
Overlay Concept 44
6.2 Peripheral Devices 45
Chapter7 Ethernet Board 48
Ethernet Board Parts Names 49
8.1 Overview 50
8.2 Product Specifications 51
(A) Status indicator LEDs 52
(B) DIP switch (SW101) 53
Setting the node address 53
Setting the bit rate 54
(C) DeviceNet connector 54
8.2.2 General Specifications 55
(1) Input Data 56
(2) Output Data 57
Robot initialization finished 57
Continue start permitted 57
Command process finished 57
Status area odd parity 57
(Version 1.5 or later) 63
(Version 1.7 or later) 66
8.7 Error Code Table 69
9.1 Overview 72
9.1.1 Features 73
9.2 Product Specifications 76
0: OFF 1: ON 79
9.2.2 General Specifications 81
9.3 ALLOCATING I/O AREAS 82
CONTROLLER INTERFACE MANUAL 84
Trunk lines and drop lines 85
Terminating resistors 85
Communication power supply 86
Connection style 86
Trunk line length 87
Drop line length 87
What is “scanlist”? 88
Scanlist creation procedure 88
Press [F9 SlaveMap] 89
Screen explanation 91
Explanation about screen 98
Input area display screen 98
Output area display screen 98
[Scan] and [Change] keys 98
DeviceNet 109
10.1 Overview 112
Slave Board 113
10.1.3 Specifications 114
→ CIF30-DPS → Hil_7504.GSD 117
Model COM-2(PC)F 118
Manufactured by CONTEC 118
Extension Board 119
Assignment 120
11.7 Limited Warranty 122
Remove the side plate 124
PART 3 OTHER OPTIONS 130
13.3 Names of the Components 131
13.4 External Dimensions 132
Preparing a power supply 133
13.6 Precautions 134

Comentarios a estos manuales

Sin comentarios

Denso RC5 Especificaciones Pagina 119

Comentarios a estos manuales